Crop nutrition
Fertilizer calculator: how to figure pounds per acre
By the Sutter Butte Dusters team · · 7 min read

A fertilizer calculator turns a nutrient target into pounds of product per acre. The math uses two numbers: the nutrient rate you want and the analysis on the bag or tank. This post shows each step, with worked examples for urea, ammonium sulfate, a blend and a liquid product.
This post gives the math, not a rate. The target rate for your field comes from a soil or tissue test and from your crop adviser. Our guide to soil sampling explains how to take the samples that set that target.
What does a fertilizer analysis mean?
The fertilizer analysis is the three numbers on the label, such as 16-20-0. Each number is a percent by weight. The first number is nitrogen (N). The second is phosphate (P2O5). The third is potash (K2O).
A fourth number, when present, is usually sulfur (S). Ammonium sulfate, for example, has the analysis 21-0-0-24S. So 100 pounds of ammonium sulfate holds 21 pounds of nitrogen and 24 pounds of sulfur.
The label states phosphorus as P2O5 and potassium as K2O. These compounds are not actually in the fertilizer. They are the traditional way to express the content, as Penn State Extension explains. Most soil test reports and crop advisers also give phosphorus and potassium rates as P2O5 and K2O.
How do you calculate fertilizer rate per acre?
Use one formula for every dry product. Divide the nutrient rate by the nutrient percent, written as a decimal.
Product pounds per acre = nutrient pounds per acre / (percent nutrient / 100)
This is how to calculate fertilizer for any single nutrient. The answer tells you how much fertilizer per acre to apply to reach the target. The examples below use round targets to show the arithmetic only.
Example 1: urea, 46-0-0
Your adviser calls for 30 pounds of nitrogen per acre. Urea is 46% nitrogen.
30 / 0.46 = 65.2 pounds of urea per acre
Example 2: ammonium sulfate, 21-0-0-24S
The same 30 pounds of nitrogen per acre comes from ammonium sulfate. It is 21% nitrogen and 24% sulfur.
30 / 0.21 = 142.9 pounds of ammonium sulfate per acre
That product also supplies sulfur: 142.9 x 0.24 = 34.3 pounds of sulfur per acre. Ammonium sulfate needs more than twice the product weight of urea for the same nitrogen. That difference changes the number of loads, the trucking and the cost of the job.
The California rice guidelines note this point. They say that ammonium sulfate is popular for an aerial top-dress because its lower nitrogen content and greater mass help the spread stay even. The same guidelines rate ammonium sulfate and urea as equally efficient when the soil has enough sulfur. Source: CDFA FREP fertilization guidelines for rice.
Example 3: a blend, 16-20-0
A blend supplies two or more nutrients in fixed proportions. Calculate the rate from the nutrient that matters most, and then check the others.
Your adviser calls for 40 pounds of P2O5 per acre. The blend is 20% P2O5.
40 / 0.20 = 200 pounds of 16-20-0 per acre
That rate also supplies nitrogen: 200 x 0.16 = 32 pounds of nitrogen per acre. Subtract those 32 pounds from the nitrogen plan for the season. If the blend gives too much of one nutrient, ask your adviser about a different product.
How do you convert P2O5 to P and K2O to K?
Some lab reports and research papers give elemental phosphorus (P) or potassium (K). Penn State Extension gives these factors:
- Percent P2O5 x 0.44 = percent P
- Percent K2O x 0.83 = percent K
The same factors work on pounds. In Example 3, 40 pounds of P2O5 x 0.44 = 17.6 pounds of P. A product with 60 pounds of K2O, such as 100 pounds of potash (0-0-60), holds 60 x 0.83 = 49.8 pounds of K.
To go the other way, divide by the factor. A target of 20 pounds of P per acre is 20 / 0.44 = 45.5 pounds of P2O5 per acre. Always confirm which form your soil report uses before you divide by the analysis.
How do you calculate pounds of nitrogen per acre in a liquid fertilizer?
A liquid product is sold by the gallon, but the analysis is a percent by weight. So you need the weight of one gallon. Use this formula:
Nutrient pounds per gallon = pounds per gallon x (percent nutrient / 100)
Then divide the target by the pounds of nutrient in each gallon.
Gallons per acre = nutrient pounds per acre / nutrient pounds per gallon
The University of Georgia Extension lists 32-0-0 solution at 11.06 pounds per gallon, in a 2023 table. It lists 28-0-0 at 10.65 pounds per gallon.
Example 4: 32-0-0 solution
One gallon holds 11.06 x 0.32 = 3.54 pounds of nitrogen. For 30 pounds of nitrogen per acre:
30 / 3.54 = 8.5 gallons per acre
The same target with 28-0-0 takes 30 / 2.98 = 10.1 gallons per acre. The weight of a gallon changes with the product and the temperature. Ask your supplier for the weight of the product in your tank.
Common fertilizers and pounds of product per 10 pounds of nutrient
This table works as a quick fertilizer calculator for common products. It divides 10 pounds of nutrient by each analysis. Multiply the result by your target, divided by 10. For example, 30 pounds of nitrogen from urea is 3 x 21.7 = 65.1 pounds, which matches Example 1 within rounding.
| Product | Analysis | Nutrient used | Pounds of product per 10 pounds of nutrient |
|---|---|---|---|
| Urea | 46-0-0 | N | 21.7 |
| Ammonium sulfate | 21-0-0-24S | N | 47.6 |
| Blend | 16-20-0 | N | 62.5 |
| Blend | 16-20-0 | P2O5 | 50.0 |
| Monoammonium phosphate | 11-52-0 | P2O5 | 19.2 |
| Potash (potassium chloride) | 0-0-60 | K2O | 16.7 |
| Solution, 11.06 lb per gallon | 32-0-0 | N | 31.3 (2.83 gallons) |
| Solution, 10.65 lb per gallon | 28-0-0 | N | 35.7 (3.35 gallons) |
| Solution, 11.65 lb per gallon | 10-34-0 | P2O5 | 29.4 (2.52 gallons) |
Liquid weights are from the UGA Extension table. Analyses vary between suppliers, so use the analysis on your label or bag tag.
How much fertilizer does a whole field need, and how many loads?
Multiply the rate per acre by the acres. Then divide the total by the load that the aircraft carries.
Total product = product per acre x acres
Number of loads = total product / load size, rounded up
Example 5: dry product on 160 acres
A 160-acre rice field gets 142.9 pounds of ammonium sulfate per acre, from Example 2.
160 x 142.9 = 22,864 pounds, about 11.4 tons
For the arithmetic, use an example load of 2,000 pounds. The real load depends on the aircraft, the product and the weather, so your operator gives that number.
22,864 / 2,000 = 11.4, so the job needs 12 loads
Example 6: liquid product on 160 acres
The same field gets 8.5 gallons per acre of 32-0-0, from Example 4.
160 x 8.5 = 1,360 gallons
Our Air Tractor 602 has a 630-gallon hopper. By volume, 1,360 / 630 = 2.2, so the job needs at least 3 loads. But liquid fertilizer is heavy. A full 630-gallon hopper of this solution weighs 630 x 11.06 = 6,968 pounds. Weight limits on the day can keep the load under a full hopper, which adds loads.
For spray mixes, the same load math appears in our gallons per acre calculator guide.
Step by step: use the fertilizer calculator method on your field
Do not guess the target rate. A wrong rate wastes product or costs yield.
- Get a soil or tissue test for the field.
- Get the nutrient target in pounds per acre from your crop adviser.
- Confirm whether the target is N, P2O5, K2O, P or K.
- Convert P to P2O5, or K to K2O, if needed.
- Read the analysis on the label or bag tag.
- Divide the target by the nutrient percent as a decimal.
- For a liquid, divide by the nutrient pounds per gallon instead.
- Check what else the product supplies, such as nitrogen in a blend.
- Multiply the rate by the acres for the total product.
- Ask the operator for the load size, and divide the total by it.
- Round the number of loads up to a whole load.
- Write the product, rate and acres on the work order.
How Sutter Butte Dusters applies fertilizer
We apply dry and liquid fertilizer by air in Sutter, Yuba, Butte, Glenn, Colusa, Placer and Yolo counties. That includes top-dress nitrogen on flooded rice, where a ground rig cannot go. See our aerial fertilizer application page for the details. Send us the product, the rate per acre and the acres from your adviser, and we plan the loads. For insect spray timing later in the season, try our free NorCal spray timing tracker. When your numbers are ready, get a fertilizer flight quote.
Questions
The amount depends on the nutrient target for your field, which comes from a soil or tissue test and your crop adviser. Once you have the target in pounds of nutrient per acre, divide it by the nutrient percent in the product. The result is pounds of product per acre.
Urea is 46% nitrogen, so 50 pounds of nitrogen takes 50 / 0.46 = 108.7 pounds of urea. The same nitrogen from ammonium sulfate, at 21% nitrogen, takes 238.1 pounds. Always use the analysis on your own label, because products vary.
A 2023 University of Georgia Extension table lists 32-0-0 solution at 11.06 pounds per gallon. Multiply 11.06 by 0.32 to get about 3.54 pounds of nitrogen per gallon. The weight changes with the product and the temperature, so ask your supplier for the weight of your product.
The numbers are percents by weight of nitrogen, phosphate (P2O5) and potash (K2O). So 100 pounds of 16-20-0 holds 16 pounds of nitrogen, 20 pounds of P2O5 and no potash. A fourth number, when present, is usually sulfur.

